2G 3G 4G CDMA850 PCS1900 4G 2600 Tri band signal repeaters
What is a mobile signal booster and how dose the booster work?
Mobile signal booster (also known as mobile signal repeater / amplifier) are designed to amplify a weak outdoor signal and provide a strong inside signal to an poor signal area.
A mobile signal repeater kit has three main parts, an outdoor antenna that receives the initial signal, the repeater that boosts the signal, and an indoor antenna that broadcasts the boosted signal to the inside area that needs it. Antennas and repeater are connected together with high quality cable
We provides signal boosters kits for any Homes, Offices, Cars, RV's, Boats and more. All amplifier kits come with Indoor and Outdoor Antennas, Cables, Power adapters and more.
HPC-CPL-27 Tri band repeater Features:
1.With unique appearance design, have good cooling function
2.With MGC function,(Manual Gain Control), Customer can adjust the Gain as needed ;
3.With DL signal LED display, help to install the outdoor antenna at the best state;
4.With AGC and ALC, make repeater work stable .
5.PCB with isolation function ,make UL and DL signal not influence each other,
6.Low intermodulation, high Gain ,stable Output power
HPC-CPL-27 repeater Inside and Outside Design
HPC-CPL-27 Tri band repeater is to support any two mobile band existing in the world to help end users to improve mobile signals for much better phone call quality and smoother data transmission. It is designed to support coverage area max can up to 3500 square meters with proper engineering. Below are the main features.
1.The consumer repeater is an ideal solution for providing a cost effective improvement in cellular in-building coverage of a home, office, restaurant or building, in the quickest time possible.
2.Manual gain control (MGC) available for both uplink and downlink to adjust the gain value for proper coverage during installation or maintenance.
3.To maintain safe and specific output signal levels and give alarms on self-oscillation, the repeater has built-in AGC and ALC circuits, which can automatically control the gain of the repeater depending upon the strength of input signals.
4.Auto shut off function available for both uplink and downlink to avoid deep self-oscilation from jamming the towers, saving your trouble from operators.
5.Wide band feature enables all devices operating within the wide frequency range of the repeater to see an improvement in performance.
6.Multiple phones and other handheld devices throughout a building can benefit from a wireless repeater.
7.Supports up to (500) users / calls simultaneously.
8.Extended phone battery life. (Your phone does not need to put out as much power due to improved reception.)
Specification of HPC-CPL-27 Tri band repeater:
Electrical specification |
Uplink |
Downlink |
||
Frequency Range |
CDMA |
824 ~ 849 MHz |
869 ~ 894 MHz |
|
PCS |
1850 ~ 1910 MHz |
1930 ~ 1990 MHz |
||
4G LTE |
2500-2570MHz |
2620-2690MHz |
||
Max .Gain |
≥ 70dB |
≥ 75dB |
||
Max .Output Power |
≥ 24dBm |
≥ 27dBm |
||
MGC ( Step Attenuation ) |
≥ 31dB / 1dB step |
|||
Automatic Level Control |
≥ 20dB |
|||
Gain Flatness |
GSM & CDMA |
Tpy≤ 6dB(P-P); DCS,PCS ≤ 8dB(P-P) |
||
WCDMA |
≤ 2dB/ 3.84MHz,Full Band ≤ 5dB(P-P) |
|||
Noise Figure |
≤ 5dB |
|||
VSWR |
≤ 2.0 |
|||
Group Delay |
≤ 1.5μs |
|||
Frequency stability |
≤ 0.01ppm |
|||
Spurious Emission & Output inter-modulation |
GSM Meet ETSI TS 151 026 V 6.1.0 |
|||
WCDMA Meet 3GPP TS 25.143 ( V 6.2.0 ) | ||||
CDMA Meet IS95 & CDMA2000 | ||||
WCDMA System |
Spurious Emission Mask |
Meet 3GPP TS 25.143 ( V 6.2.0 ) |
||
Modulation Accuracy |
≤ 12.5% |
|||
Peak Code Domain Error |
≤ -35dB@Spreading Factor 256 |
|||
CDMA System |
Rho |
ρ > 0.980 |
||
ACPR |
Meet IS95 & CDMA2000 |
|||
Mechanical Specifications |
Standard |
|||
I /O Port |
N-Female |
|||
Impedance |
50 ohm |
|||
Operating Temperature |
-25ºC~+55ºC |
|||
Environment Conditions |
IP40 |
|||
Dimensions |
220x320x40mm |
|||
Weight |
≤ 3.50Kg |
|||
Power Supply |
Input AC90-264V,output DC 5V / 6A |
|||
LED Alarm |
Standard |
|||
Power LED |
Power Indicator |
|||
UL LED |
Be lighted when there is phone calling |
|||
DL 1 |
Be lighted when Outdoor signal is -65dB |
|||
DL 2 |
Be lighted when Outdoor signal only -55dB |
|||
DL 3 |
Be lighted when Outdoor signal only -50dB |
The installtion of the Repeater
Outdoor antenna ( for receiving the signal from the BTS ) + Cable ( transfering the received signal) + Repeater ( for amplifying the received signal) + cable( for transfering the amplified signal) + indoor antenna( for shooting the amplified signal),